综合飞行/推力控制系统的智能设计

在介绍正规矩阵参数优化方法和着舰导引控制系统的基础上,为提高舰载飞机的操纵性能,采用智能设计软件IntelDes3．0设计了具有鲁棒性的着舰飞行,推力综合控制系统。基于飞机纵向非线性运动方程的数值仿真结果表明,设计的控制系统对阶跃输入的响应性能良好,鲁棒性较强。     

Foreign Object Damage to Fan Rotor Blades of Aeroengine Part Ⅱ： Numerical Simulation of Bird Impact

Bird impact is one of the most dangerous threats to flight safety. The consequences of bird impact can be severe and, therefore, the aircraft components have to be certified for a proven level of bird impact resistance before being put into service. The fan rotor blades of aeroengine are the components being easily impacted by birds. It is necessary to ensure that the fan rotor blades should have adequate resistance against the bird impact, to reduce the flying accidents caused by bird impacts. Using the contacting-impacting algorithm, the numerical simulation is carded out to simulate bird impact. A three-blade computational model is set up for the fan rotor blade having shrouds. The transient response curves of the points corresponding to measured points in experiments, displacements and equivalent stresses on the blades are obtained during the simulation. From the comparison of the transient response curves obtained from numerical simulation with that obtained from experiments, it can be found that the variations in measured points and the corresponding points of simulation are basically the same. The deforming process, the maximum displacements and the maximum equivalent stresses on blades are analyzed. The numerical simulation verifies and complements the experiment results.     

固体药柱超声波特征扫描系统研制

对固体火箭发动机药柱的超声检测方法进行了研究,介绍了超声特征扫描成像原理及缺陷检测方法,研制了药柱超声波特征扫描系统,并用低频组合探头对药柱进行了检测.试验表明,设计的超声特征扫描系统可采用幅度成像、深度成像方法显示药柱的缺陷.     

基于SPARC V8结构处理器的计算机系统设计

首先介绍了国内外计算机SPARC体系结构的研究现状,指出SPARC体系结构已成为国际上流行的处理器结构之一,而且众多航天机构也采用了SPARC结构的处理器设计其航天器的计算机系统。随后,着重说明了SPARC V8的组成结构以及国内外基于SPARC V8结构设计实现的处理器。最后给出了基于国产SPARC V8结构处理器BM3802设计实现的最小系统组成结构。     

电推进系统压力调节单元的建模和分析

 建立了电推进系统压力调节单元的数学模型,利用Matlab/Simulink软件分析几个重要参数对系统的影响。仿真结果表明,采用bang-bang控制策略具有较高的控制精度,可满足系统的指标要求。     

Aerodynamic Design and Analysis of a Low-reaction Axial Compressor Stage

There is introduced a new low-reaction, highly-loaded axial compressor design concept which is coupled with boundary layer suction method. The characteristic features of the concept are made clear through its comparison with the MIT boundary layer suction compressor. Also are pointed out the potential applications of this concept as well as its key technological problems. Based on this concept, a single-stage, low-reaction and low-speed axial compressor is constructed in association with analysis and computation of boundary layer suction on vanes with the aid of a three-dimensional numerical approach. The results attest to the effectiveness of this way to control separation in blade cascades by the boundary layer suction and the feasibility of this proposed design concept.     

直升机动力传动系统扭转振动整体传递矩阵分析

研究了复杂多轴齿轮传动系统整体传递矩阵方法及在直升机动力传动系统扭转振动分析中的应用.首先说明了直升机传动系统传递矩阵方法力学模型,推导了传动系统中典型齿轮副啮合传递矩阵、并车级和行星级齿轮啮合传递矩阵,说明了这种具有多种齿轮副啮合的复杂多轴系统整体传递矩阵模型组集方法,最后用这种方法进行了典型直升机动力传动系统扭转振动特性分析,讨论了这种直升机动力系统振动特性的特点.      

孔间距和前倾角对进出口扩张形气膜孔流量系数的影响(英文)

Discharge coefficients of 3-in-1 hole of three inclination angles and three spacing between holes are presented which described the discharge behavior of a row of holes. The inlet and outlet of the 3-in-1 hole both have a 15° lateral expansion. The flow conditions considered are mainstream turbulence intensities and density ratios of secondary flow to mainstream. The momentum flux ratios varied in the range from 1 to 4. The comparison is made of the discharge coefficients of three shaped holes to find an optimal hole with low flow loss. The results show that the discharge coefficients of 3-in- 1 hole are highest in three shaped holes and therefore this article is focused on the measurements of discharge coefficients of 3-in-1 hole for various geometries and aerodynamic parameters. The measured results of 3-in-1 hole indicate that turbulence intensities, density ratios and momentum flux ratios have weak influence on discharge coefficients for inclination angle of 20°. The high turbulence intensity yields the small discharge coefficients for inclination angle of 45° and 90°. The increased both momentum flux ratios and density ratios lead to the increased discharge coefficients for inclination angle of 45° and 90°. The increased inclination angle causes the rapidly increased discharge coefficients. There is a weak dependence of discharge coefficients on hole pitches.     

角速率输入下圆锥补偿算法的一般形式

传统圆锥补偿算法直接应用于由速率陀螺组成的捷联惯导系统时,算法误差明显增大.为抑制算法误差,提出了一种以角速率为输入信号,任意子样数圆锥补偿算法(包括改进算法)的一般形式,并在典型圆锥运动条件下以算法漂移误差最小为优化准则,推导了相应的圆锥补偿系数方程和算法误差表达式.利用给出的公式,求解一个线性方程组即可得到圆锥补偿系数,可方便快捷的设计任意子样数的角速率圆锥补偿算法以及改进算法.仿真结果表明,所设计的改进算法比同子样数常规角速率圆锥补偿算法在精度上有明显提高.      

用于识别两颗故障卫星的RAIM算法

提出了一种可以识别两颗故障卫星的接收机自主完好性监测算法.将最优奇偶矢量法应用于两颗故障卫星识别,指出由于故障偏差可能会抵消而使得正确识别率较低.对最优奇偶矢量法进行了改进,利用对单颗卫星故障敏感的最优奇偶矢量对所有可能的两颗故障卫星组合分别构造两个新的奇偶矢量,用于两颗故障卫星的检测和识别.计算机仿真结果显示,改进后的算法与直接利用最优奇偶矢量法相比,可以显著提高两颗故障卫星正确识别率,识别率可超过90%.同时,改进算法的奇偶矢量构造方法简单,计算量将减少90%以上,更有利于工程实现.